Port 1135 OMNIVISION
Port 1135 is the IANA-assigned omnivision port for OmniVision Communication Service (TCP / UDP).
What is port 1135 used for?
Port 1135 is assigned to omnivision and uses TCP / UDP. The IANA registry describes the service as “OmniVision Communication Service”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.
Ports are the transport-layer address a service listens on. A client that wants to reach omnivision connects to port 1135. A TCP connection is refused when nothing is listening, while a UDP request simply goes unanswered. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 1135 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [Serge_Vacquier].
Check and block port 1135
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :1135'
sudo ss -ulpn 'sport = :1135'Check on Windows
Get-NetTCPConnection -LocalPort 1135 -State Listen -ErrorAction SilentlyContinue
Get-NetUDPEndpoint -LocalPort 1135 -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 1135/tcp
sudo ufw deny 1135/udpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 1135 -j DROP
sudo iptables -A INPUT -p udp --dport 1135 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 1135 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 1135 is usually used
Most traffic on port 1135 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Application backends and supporting services that use a fixed registered number.
- Containers or local stacks that publish the port on the host.
- Firewall and exposure reviews before the service goes to production.
Probe the port
Confirm something is listening before you debug the client. This checks a TCP handshake on the port.
nc -vz 127.0.0.1 1135Common problems with port 1135
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 1135. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :1135' or sudo lsof -i :1135. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 1135 at a glance
| Port number | 1135 |
|---|---|
| Service name | omnivision |
| Transport protocol | TCP / UDP |
| Category | Application services |
| Range | Registered port (1024–10000) |
| Risk level | Standard/Low |
| Registered assignee | [Serge_Vacquier] |
| Registry description | OmniVision Communication Service |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 1135 used for?
Port 1135 (OMNIVISION) uses TCP / UDP. OmniVision Communication Service.
How do I check if port 1135 is open?
On Linux run `sudo ss -tlpn 'sport = :1135'` and `sudo ss -ulpn 'sport = :1135'`. On Windows run `Get-NetTCPConnection -LocalPort 1135 -State Listen -ErrorAction SilentlyContinue` and `Get-NetUDPEndpoint -LocalPort 1135 -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 1135; empty output usually means nothing is bound to it.
How do I block port 1135?
With UFW run `sudo ufw deny 1135/tcp` and `sudo ufw deny 1135/udp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 1135 -j DROP` and `sudo iptables -A INPUT -p udp --dport 1135 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 1135 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 1132 · kvm-via-ipKVM-via-IP Management Service
- Port 1138 · encrypted-adminencrypted admin requests IANA assigned this well-formed service name…
- Port 1131 · caspsslCAC App Service Protocol Encripted
- Port 1139 · evmEnterprise Virtual Manager
- Port 1127 · kwdb-commnKWDB Remote Communication
- Port 1140 · autonocAutoNOC Network Operations Protocol
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy