Port 13720 BPRD
Port 13720 is the IANA-assigned bprd port for BPRD Protocol (VERITAS NetBackup) (TCP / UDP).
What is port 13720 used for?
Port 13720 is assigned to bprd and uses TCP / UDP. The IANA registry describes the service as “BPRD Protocol (VERITAS NetBackup)”. It sits above the registered range, where most numbers are transient client ports. A fixed high port is worth documenting precisely because tooling often assumes the default.
Ports are the transport-layer address a service listens on. A client that wants to reach bprd connects to port 13720. A TCP connection is refused when nothing is listening, while a UDP request simply goes unanswered. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 13720 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [Jeff_Holmbeck].
Check and block port 13720
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :13720'
sudo ss -ulpn 'sport = :13720'Check on Windows
Get-NetTCPConnection -LocalPort 13720 -State Listen -ErrorAction SilentlyContinue
Get-NetUDPEndpoint -LocalPort 13720 -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 13720/tcp
sudo ufw deny 13720/udpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 13720 -j DROP
sudo iptables -A INPUT -p udp --dport 13720 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 13720 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 13720 is usually used
Most traffic on port 13720 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Custom or vendor-specific services configured to use a fixed high number.
- Short-lived container or test environments that publish the port on the host.
- Firewall planning, since most other high ports are transient client ports.
Probe the port
Confirm something is listening before you debug the client. This checks a TCP handshake on the port.
nc -vz 127.0.0.1 13720Common problems with port 13720
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 13720. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :13720' or sudo lsof -i :13720. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 13720 at a glance
| Port number | 13720 |
|---|---|
| Service name | bprd |
| Transport protocol | TCP / UDP |
| Category | Custom high ports |
| Range | High port (10001–65535) |
| Risk level | Standard/Low |
| Registered assignee | [Jeff_Holmbeck] |
| Registry description | BPRD Protocol (VERITAS NetBackup) |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 13720 used for?
Port 13720 (BPRD) uses TCP / UDP. BPRD Protocol (VERITAS NetBackup).
How do I check if port 13720 is open?
On Linux run `sudo ss -tlpn 'sport = :13720'` and `sudo ss -ulpn 'sport = :13720'`. On Windows run `Get-NetTCPConnection -LocalPort 13720 -State Listen -ErrorAction SilentlyContinue` and `Get-NetUDPEndpoint -LocalPort 13720 -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 13720; empty output usually means nothing is bound to it.
How do I block port 13720?
With UFW run `sudo ufw deny 13720/tcp` and `sudo ufw deny 13720/udp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 13720 -j DROP` and `sudo iptables -A INPUT -p udp --dport 13720 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 13720 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 13218 · emc-vcas-udpEMV Virtual CAS Service Discovery
- Port 13721 · bpdbmBPDBM Protocol (VERITAS NetBackup)
- Port 13216 · bcslogcBlack Crow Software application logging
- Port 13722 · bpjava-msvcBP Java MSVC Protocol
- Port 12865 · netperfcontrol port for the netperf benchmark
- Port 13724 · vnetdVeritas Network Utility
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy