Port 2408 RAILGUN-WEBACCL
Port 2408 is the IANA-assigned railgun-webaccl port for CloudFlare Railgun Web Acceleration Protocol (TCP).
What is port 2408 used for?
Port 2408 is assigned to railgun-webaccl and uses TCP. The IANA registry describes the service as “CloudFlare Railgun Web Acceleration Protocol”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.
Ports are the transport-layer address a service listens on. A client that wants to reach railgun-webaccl connects to port 2408. If nothing is listening, the connection is refused. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 2408 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [CloudFlare].
Check and block port 2408
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :2408'Check on Windows
Get-NetTCPConnection -LocalPort 2408 -State Listen -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 2408/tcpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 2408 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 2408 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 2408 is usually used
Most traffic on port 2408 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Serving a website, API or reverse-proxy traffic that clients reach on port 2408.
- Load-balancer and uptime checks probing the port before routing requests.
- Local development, where a browser or curl calls the service on localhost:2408.
Send a test request
Start a local web server, then ask the port for response headers. Replace 127.0.0.1 with the host you are testing.
curl -I http://127.0.0.1:2408Common problems with port 2408
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 2408. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :2408' or sudo lsof -i :2408. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 2408 at a glance
| Port number | 2408 |
|---|---|
| Service name | railgun-webaccl |
| Transport protocol | TCP |
| Category | Web and HTTP |
| Range | Registered port (1024–10000) |
| Risk level | Standard/Low |
| Registered assignee | [CloudFlare] |
| Registry description | CloudFlare Railgun Web Acceleration Protocol |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 2408 used for?
Port 2408 (RAILGUN-WEBACCL) uses TCP. CloudFlare Railgun Web Acceleration Protocol.
How do I check if port 2408 is open?
On Linux run `sudo ss -tlpn 'sport = :2408'`. On Windows run `Get-NetTCPConnection -LocalPort 2408 -State Listen -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 2408; empty output usually means nothing is bound to it.
How do I block port 2408?
With UFW run `sudo ufw deny 2408/tcp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 2408 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 2408 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 2404 · iec-104IEC 60870-5-104 process control over IP
- Port 2415 · codima-rtpCodima Remote Transaction Protocol
- Port 2263 · ecwcfgECweb Configuration Service
- Port 2784 · www-devworld wide web - development
- Port 2193 · drwcsDr.Web Enterprise Management Service
- Port 3443 · ov-nnm-websrvOpenView Network Node Manager WEB Server
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy