Port 27010 FLEX-LMADMIN
Port 27010 is the IANA-assigned flex-lmadmin port for A protocol for managing license services (TCP).
What is port 27010 used for?
Port 27010 is assigned to flex-lmadmin and uses TCP. The IANA registry describes the service as “A protocol for managing license services”. It sits above the registered range, where most numbers are transient client ports. A fixed high port is worth documenting precisely because tooling often assumes the default.
Ports are the transport-layer address a service listens on. A client that wants to reach flex-lmadmin connects to port 27010. If nothing is listening, the connection is refused. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 27010 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [Flexera].
Check and block port 27010
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :27010'Check on Windows
Get-NetTCPConnection -LocalPort 27010 -State Listen -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 27010/tcpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 27010 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 27010 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 27010 is usually used
Most traffic on port 27010 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Custom or vendor-specific services configured to use a fixed high number.
- Short-lived container or test environments that publish the port on the host.
- Firewall planning, since most other high ports are transient client ports.
Probe the port
Confirm something is listening before you debug the client. This checks a TCP handshake on the port.
nc -vz 127.0.0.1 27010Common problems with port 27010
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 27010. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :27010' or sudo lsof -i :27010. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 27010 at a glance
| Port number | 27010 |
|---|---|
| Service name | flex-lmadmin |
| Transport protocol | TCP |
| Category | Custom high ports |
| Range | High port (10001–65535) |
| Risk level | Standard/Low |
| Registered assignee | [Flexera] |
| Registry description | A protocol for managing license services |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 27010 used for?
Port 27010 (FLEX-LMADMIN) uses TCP. A protocol for managing license services.
How do I check if port 27010 is open?
On Linux run `sudo ss -tlpn 'sport = :27010'`. On Windows run `Get-NetTCPConnection -LocalPort 27010 -State Listen -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 27010; empty output usually means nothing is bound to it.
How do I block port 27010?
With UFW run `sudo ufw deny 27010/tcp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 27010 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 27010 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 26263 · k3software-cliK3 Software-Client
- Port 27016 · chlenixCloud hosting environment network
- Port 26262 · k3software-svrK3 Software-Server
- Port 27442 · jesmsjcJob controller service
- Port 26133 · scscpSymbolic Computation Software Composability Protocol
- Port 27782 · ars-vistaARS VISTA Application
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy