Port 32400 PLEX
Port 32400 is the IANA-assigned plex port for Plex multimedia (TCP).
What is port 32400 used for?
Port 32400 is assigned to plex and uses TCP. The IANA registry describes the service as “Plex multimedia”. It sits above the registered range, where most numbers are transient client ports. A fixed high port is worth documenting precisely because tooling often assumes the default.
Ports are the transport-layer address a service listens on. A client that wants to reach plex connects to port 32400. If nothing is listening, the connection is refused. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 32400 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [Plex_Inc.].
Check and block port 32400
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :32400'Check on Windows
Get-NetTCPConnection -LocalPort 32400 -State Listen -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 32400/tcpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 32400 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 32400 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 32400 is usually used
Most traffic on port 32400 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Custom or vendor-specific services configured to use a fixed high number.
- Short-lived container or test environments that publish the port on the host.
- Firewall planning, since most other high ports are transient client ports.
Probe the port
Confirm something is listening before you debug the client. This checks a TCP handshake on the port.
nc -vz 127.0.0.1 32400Common problems with port 32400
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 32400. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :32400' or sudo lsof -i :32400. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 32400 at a glance
| Port number | 32400 |
|---|---|
| Service name | plex |
| Transport protocol | TCP |
| Category | Custom high ports |
| Range | High port (10001–65535) |
| Risk level | Standard/Low |
| Registered assignee | [Plex_Inc.] |
| Registry description | Plex multimedia |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 32400 used for?
Port 32400 (PLEX) uses TCP. Plex multimedia.
How do I check if port 32400 is open?
On Linux run `sudo ss -tlpn 'sport = :32400'`. On Windows run `Get-NetTCPConnection -LocalPort 32400 -State Listen -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 32400; empty output usually means nothing is bound to it.
How do I block port 32400?
With UFW run `sudo ufw deny 32400/tcp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 32400 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 32400 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 32249 · t1distproc60T1 Distributed Processor
- Port 32483 · apm-linkAccess Point Manager Link
- Port 32034 · iracinghelperiRacing helper service
- Port 32767 · filenet-powsrmFileNet BPM WS-ReliableMessaging Client
- Port 31949 · iceedcp-rxEmbedded Device Configuration Protocol RX IANA assigned this…
- Port 32772 · filenet-paFileNET Process Analyzer
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy