Port 465 SUBMISSIONS
Port 465 has a different IANA assignment for each transport protocol: TCP submissions, urd; UDP igmpv3lite.
What is port 465 used for?
Port 465 carries a different IANA service on each transport protocol: TCP submissions, urd; UDP igmpv3lite. It sits in the well-known range, which operating systems reserve for core network services, so software expects it at this number by default. The same port is also registered under urd, igmpv3lite.
Each transport reaches a different service on this number, so match the protocol to the service you are diagnosing. A TCP check says nothing about a UDP listener on the same port, and the reverse is also true. Both transports still bind to the same number, which is why two processes can collide even when they use different protocols.
Use the commands below to confirm whether port 465 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [IESG]. Reference: [RFC 8314].
Check and block port 465
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :465'
sudo ss -ulpn 'sport = :465'Check on Windows
Get-NetTCPConnection -LocalPort 465 -State Listen -ErrorAction SilentlyContinue
Get-NetUDPEndpoint -LocalPort 465 -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 465/tcp
sudo ufw deny 465/udpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 465 -j DROP
sudo iptables -A INPUT -p udp --dport 465 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 465 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 465 is usually used
Most traffic on port 465 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Mail clients sending messages through a relay or fetching them from a mailbox.
- Mail servers exchanging messages for a domain or syncing folders with clients.
- Deliverability, authentication and TLS tests that connect directly to the mail service.
Test SMTPS
Port 465 expects TLS from the first byte. The handshake confirms the relay is listening.
openssl s_client -connect mail.example.com:465Common problems with port 465
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 465. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :465' or sudo lsof -i :465. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 465 at a glance
| Port number | 465 |
|---|---|
| Service name | submissions |
| Aliases | urd, igmpv3lite |
| Transport protocol | TCP / UDP |
| Assignments by protocol |
|
| Category | |
| Range | Well-known port (0–1023) |
| Risk level | Standard/Low |
| Registered assignee | [IESG] |
| Reference | [RFC 8314] |
| Registry description | Message Submission over TLS protocol |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 465 used for?
Port 465 (SUBMISSIONS). The IANA registry assigns a different service on each transport protocol: TCP submissions, urd; UDP igmpv3lite.
How do I check if port 465 is open?
On Linux run `sudo ss -tlpn 'sport = :465'` and `sudo ss -ulpn 'sport = :465'`. On Windows run `Get-NetTCPConnection -LocalPort 465 -State Listen -ErrorAction SilentlyContinue` and `Get-NetUDPEndpoint -LocalPort 465 -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 465; empty output usually means nothing is bound to it.
How do I block port 465?
With UFW run `sudo ufw deny 465/tcp` and `sudo ufw deny 465/udp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 465 -j DROP` and `sudo iptables -A INPUT -p udp --dport 465 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 465 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy