Port 5693 RBSYSTEM
Port 5693 is the IANA-assigned rbsystem port for Robert Bosch Data Transfer (TCP).
What is port 5693 used for?
Port 5693 is assigned to rbsystem and uses TCP. The IANA registry describes the service as “Robert Bosch Data Transfer”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.
Ports are the transport-layer address a service listens on. A client that wants to reach rbsystem connects to port 5693. If nothing is listening, the connection is refused. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 5693 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [Syntegon_Technology_GmbH].
Check and block port 5693
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :5693'Check on Windows
Get-NetTCPConnection -LocalPort 5693 -State Listen -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 5693/tcpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 5693 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 5693 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 5693 is usually used
Most traffic on port 5693 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Application backends and supporting services that use a fixed registered number.
- Containers or local stacks that publish the port on the host.
- Firewall and exposure reviews before the service goes to production.
Probe the port
Confirm something is listening before you debug the client. This checks a TCP handshake on the port.
nc -vz 127.0.0.1 5693Common problems with port 5693
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 5693. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :5693' or sudo lsof -i :5693. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 5693 at a glance
| Port number | 5693 |
|---|---|
| Service name | rbsystem |
| Transport protocol | TCP |
| Category | Application services |
| Range | Registered port (1024–10000) |
| Risk level | Standard/Low |
| Registered assignee | [Syntegon_Technology_GmbH] |
| Registry description | Robert Bosch Data Transfer |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 5693 used for?
Port 5693 (RBSYSTEM) uses TCP. Robert Bosch Data Transfer.
How do I check if port 5693 is open?
On Linux run `sudo ss -tlpn 'sport = :5693'`. On Windows run `Get-NetTCPConnection -LocalPort 5693 -State Listen -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 5693; empty output usually means nothing is bound to it.
How do I block port 5693?
With UFW run `sudo ufw deny 5693/tcp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 5693 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 5693 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 5689 · qmvideoQM video network management protocol
- Port 5696 · kmipKey Management Interoperability Protocol
- Port 5687 · gog-multiplayerGOG multiplayer game protocol
- Port 5682 · brightcoreBrightCore control & data transfer exchange
- Port 5700 · supportassistDell SupportAssist data center management
- Port 5681 · ncxcpNet-coneX Control Protocol
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy